View IDT70V9189L9PFI_1253784.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HIGH-SPEED 3.3V 64/32K x 9 SYNCHRONOUS PIPELINED DUAL-PORT STATIC RAM
Features:

IDT70V9189/79L

True Dual-Ported memory cells which allow simultaneous access of the same memory location High-speed clock to data access - Commercial: 6.5/7.5/9/12ns (max.) - Industrial: 9ns (max.) Low-power operation - IDT70V9189/79L Active: 500mW (typ.) Standby: 1.5mW (typ.) Flow-Through or Pipelined output mode on either port via the FT/PIPE pins Counter enable and reset features Dual chip enables allow for depth expansion without

additional logic Full synchronous operation on both ports - 4ns setup to clock and 0ns hold on all control, data, and address inputs - Data input, address, and control registers - Fast 6.5ns clock to data out in the Pipelined output mode - Self-timed write allows fast cycle time - 10ns cycle time, 100MHz operation in Pipelined output mode LVTTL- compatible, single 3.3V (0.3V) power supply Industrial temperature range (-40C to +85C) is available for selected speeds Available in a 100-pin Thin Quad Flatpack (TQFP)
Functional Block Diagram
R/W L OEL CE0L CE1L R/WR OER CE0R CE1R
1 0 0/1
1 0 0/1
FT/PIPEL
0/1
1
0
0
1
0/1
FT/PIPER
,
I/O0L - I/O8L I/O Control I/O Control
I/O0R - I/O8R
A15L(1) A0L CLKL ADSL CNTENL CNTRSTL Counter/ Address Reg. MEMORY ARRAY Counter/ Address Reg.
A15R(1) A0R CLKR ADSR CNTENR CNTRSTR
4860 drw 01
NOTE: 1. A15X is a NC for IDT70V9179.
FEBRUARY 2004
1
(c)2004 Integrated Device Technology, Inc. DSC-4860/3
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
The IDT70V9189/79 is a high-speed 64/32K x 9 bit synchronous Dual Port RAM. The memory array utilizes Dual-Port memory cells to allow simultaneous access of any address from both ports. Registers on control, data, and address inputs provide minimal setup and hold times. The timing latitude provided by this approach allows systems to be designed with very short cycle times.
Description:
With an input data register, the IDT70V9189/79 has been optimized for applications having unidirectional or bidirectional data flow in bursts. An automatic power down feature, controlled by CE0 and CE1, permits the on-chip circuitry of each port to enter a very low standby power mode. Fabricated using IDT's CMOS high-performance technology, these devices typically operate on only 500mW of power.
Pin Configuration(2,3,4)
Index
NC NC A7L A8L A9L A10L A11L A12L A13L A14L A15L(1) NC VDD NC NC NC NC CE0L CE1L CNTRSTL R/WL OEL FT/PIPEL NC NC
10099 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 2 74 3 73 72 4 1 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 71 70 69 68 67
ADSR CLKR CNTENR A0R A1R A2R A3R A4R A5R A6R NC
66 65 64 63 62 61 60 59 58 57 56 55 54 53
NC NC A6L A5L A4L A3L A2L A1L A0L CNTENL CLKL ADSL Vss Vss
01/15/04
70V9189/79PF PN100-1(5) 100-Pin TQFP Top View(6)
52 24 51 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
NC NC A7R A8R A9R A10R A11R A12R A13R A14R A15R(1) NC Vss NC NC NC NC CE0R CE1R CNTRSTR R/WR OER , FT/PIPER Vss NC
4860 drw 02
NOTES: 1. A15X is a NC for IDT70V9179. 2. All Vcc pins must be connected to power supply. 3. All GND pins must be connected to ground. 4. Package body is approximately 14mm x 14mm x 1.4mm. 5. This package code is used to reference the package diagram. 6. This text does not indicate orientation of the actual part-marking.
Vss I/O8L I/O7L I/O6L I/O5L I/O4L I/O3L I/O2L Vss I/O1L I/O0L VDD Vss I/O0R I/O1R I/O2R VDD I/O3R I/O4R I/O5R I/O6R I/O7R I/O8R NC NC
6.42 2
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Pin Names
Left Port CE0L, CE1L R/WL OEL A0L - A15L
(1)
Right Port CE0R, CE1R R/WR OER A0R - A15R
(1)
Names Chip Enables Read/Write Enable Output Enable Address Data Input/Output Clock Address Strobe Enable Counter Enable Counter Reset Flow-Through / Pipeline Power (3.3V) Ground (0V)
4860 tbl 01
I/O0L - I/O8L CLKL ADSL CNTENL CNTRSTL FT/PIPEL
I/O0R - I/O8R CLKR ADSR CNTENR CNTRSTR FT/PIPER VDD VSS
NOTE: 1. Address A15X is NC for IDT70V9179. 2. LB and UB are single buffered regardless of state of FT/PIPE. 3. CEo and CE1 are single buffered when FT/PIPE = VIL, CEo and CE1 are double buffered when FT/PIPE = VIH, i.e. the signals take two cycles to deselect.
Truth Table I--Read/Write and Enable Control(1,2,3)
OE X X X L H CLK X CE0 H X L L L CE1 X L H H H R/W X X L H X I/O0-8 High-Z High-Z DATAIN DATAOUT High-Z Deselected-Power Down Deselected-Power Down Write Read Outputs Disabled
4860 tbl 02
MODE
NOTES: 1. "H" = VIH, "L" = VIL, "X" = Don't Care. 2. ADS, CNTEN, CNTRST = X. 3. OE is an asynchronous input signal.
Truth Table II--Address Counter Control(1,2,3)
External Address An X X X Previous Internal Address X An An + 1 X Internal Address Used An An + 1 An + 1 A0 CLK ADS L(4) H H X CNTEN X L
(5)
CNTRST H H H L(4)
I/O(3) DI/O (n) DI/O(n+1) DI/O(n+1) DI/O(0) External Address Used
MODE
Counter Enabled--Internal Address generation External Address Blocked--Counter disabled (An + 1 reused) Counter Reset to Address 0
4860 tbl 03
H X
NOTES: 1. "H" = VIH, "L" = VIL, "X" = Don't Care. 2. CE0 and OE = VIL; CE1 and R/W = VIH. 3. Outputs configured in Flow-Through Output mode: if outputs are in Pipelined mode the data out will be delayed by one cycle. 4. ADS and CNTRST are independent of all other signals including CE0 and CE1. 5. The address counter advances if CNTEN = VIL on the rising edge of CLK, regardless of all other signals including CE0 and CE1.
6.42 3
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Recommended Operating Temperature and Supply Voltage
Grade Commercial Industrial Ambient Temperature(2) 0OC to +70OC -40OC to +85OC GND 0V 0V VDD 3.3V + 0.3V 3.3V + 0.3V
4860 tbl 04
Recommended DC Operating Conditions
Symbol VDD VSS VIH VIL Parameter Supply Voltage Ground Input High Voltage Input Low Voltage Min. 3.0 0 2.0V -0.3
(1)
Typ. 3.3 0
____ ____
Max. 3.6 0 VCC+0.3V 0.8
(2)
Unit V V V V
4860 tbl 05
NOTES: 1. This is the parameter TA. This is the "instant on" case temperature.
NOTES: 1. VIL > -1.5V for pulse width less than 10 ns. 2. VTERM must not exceed VDD +0.3V.
Absolute Maximum Ratings(1)
Symbol VTERM(2) Rating Terminal Voltage with Respect to GND Temperature Under Bias Storage Temperature Junction Temperature DC Output Current Commercial & Industrial -0.5 to +4.6 Unit V
Capacitance(1)
Symbol CIN COUT(3)
(TA = +25C, f = 1.0MHZ)
Parameter Input Capacitance Output Capacitance Conditions(2) VIN = 3dV VOUT = 3dV Max. 9 10 Unit pF pF
4860 tbl 07
TBIAS TSTG TJN IOUT
-55 to +125 -65 to +150 +150 50
o
C C C
o
o
mA
4860 tbl 06
NOTES: 1. These parameters are determined by device characterization, but are not production tested. 2. 3dV references the interpolated capacitance when the input and output switch from 0V to 3V or from 3V to 0V. 3. COUT also references CI/O.
NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VTERM must not exceed VDD +0.3V for more than 25% of the cycle time or 10ns maximum, and is limited to < 20mA for the period of VTERM > VDD + 0.3V. 3. Ambient Temperature Under DC Bias. NO AC Conditions. Chip Deselected.
DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V 0.3V)
70V9189/79L Symbol |ILI| |ILO| VOL VOH Parameter Input Leakage Current
(1)
Test Conditions VDD = 3.6V, VIN = 0V to VDD CE = VIH or CE1 = VIL, VOUT = 0V to VDD IOL = +4mA IOH = -4mA
Min.
___ ___ ___
Max. 5 5 0.4
___
Unit A A V V
4860 tbl 08
Output Leakage Current Output Low Voltage Output High Voltage
2.4
NOTE: 1. At VDD < 2.0V input leakages are undefined.
6.42 4
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
DC Electrical Characteristics Over the Operating Temperature Supply Voltage Range(3) (VDD = 3.3V 0.3V)
70V9189/79L6 Com'l Only Symbol ICC Parameter Dynamic Operating Current (Both Ports Active) Standby Current (Both Ports - TTL Level Inputs) Standby Current (One Port - TTL Level Inputs) Full Standby Current (Both Ports - CMOS Level Inputs) Full Standby Current (One Port - CMOS Level Inputs) Test Condition CEL and CER= VIL, Outputs Disabled, f = fMAX(1) CEL = CER = VIH f = fMAX(1) CE"A" = VIL and CE"B" = VIH(5) Active Port Outputs Disabled, f=fMAX(1) Both Ports CEL and CER > VDD - 0.2V, VIN > VDD - 0.2V or VIN < 0.2V, f = 0(2) Version COM'L IND COM'L IND COM'L IND COM'L IND L L L L L L L L L L Typ.(4) 220
____
70V9189/79L7 Com'l Only Typ. (4) 200
____
70V9189/79L9 Com'l & Ind Typ. (4) 180 180 50 50 110 110 0.4 0.4 100 100 Max. 260 280 100 120 190 205 3 6 180 195
70V9189/79L12 Com'l Only Typ. (4) 150
____
Max. 350
____
Max. 310
____
Max. 230
____
Unit mA
ISB1
70
____
130
____
65
____
130
____
40
____
80
____
mA
ISB2
150
____
250
____
140
____
245
____
100
____
175
____
mA
ISB3
0.4
____
3
____
0.4
____
3
____
0.4
____
3
____
mA
ISB4
CE"A" < 0.2V and COM'L CE"B" > VDD - 0.2V(5) VIN > VDD - 0.2V or VIN < 0.2V, Active Port, IND Outputs Disabled, f = fMAX(1)
140
____
240
____
130
____
235
____
90
____
165
____
mA
NOTES: 1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency clock cycle of 1/tCYC, using "AC TEST CONDITIONS" at input levels of GND to 3V. 2. f = 0 means no address, clock, or control lines change. Applies only to input at CMOS level standby. 3. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 4. VDD = 3.3V, TA = 25C for Typ, and are not production tested. ICC DC(f=0) = 90mA (Typ). 5. CEX = VIL means CE0X = VIL and CE1X = VIH CEX = VIH means CE0X = VIH or CE1X = VIL CEX < 0.2V means CE0X < 0.2V and CE1X > VCC - 0.2V CEX > VDD - 0.2V means CE0X > VDD - 0.2V or CE1X < 0.2V "X" represents "L" for left port or "R" for right port.
4860 tbl 09
6.42 5
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
AC Test Conditions
Input Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Reference Levels Output Load GND to 3.0V 3ns Max. 1.5V 1.5V Figures 1, 2, and 3
4860 tbl 10
3.3V
3.3V
590 DATAOUT 435 30pF DATAOUT 435
590
5pF*
4860 drw 03
4860 drw 04
Figure 1. AC Output Test load.
Figure 2. Output Test Load (For tCKLZ, tCKHZ, tOLZ, and tOHZ). *Including scope and jig.
8 7 6 5 tCD1, tCD2 (Typical, ns) 4 3 2 1 0 -1
- 10pF is the I/O capacitance of this device, and 30pF is the AC Test Load Capacitance
20 40 60 80 100 120 140 160 180 200 Capacitance (pF)
4860 drw 05
.
Figure 3. Typical Output Derating (Lumped Capacitive Load).
6.42 6
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the Operating Temperature Range (Read and Write Cycle Timing)(3) (VDD = 3.3V 0.3V, TA = 0C to +70C)
70V9189/79L6 Com'l Only Symbol tCYC1 tCYC2 tCH1 tCL1 tCH2 tCL2 tR tF tSA tHA tSC tHC tSW tHW tSD tHD tSAD tHAD tSCN tHCN tSRST tHRST tOE tOLZ tOHZ tCD1 tCD2 tDC tCKHZ tCKLZ Clock Cycle Time (Flow-Through) Clock Cycle Time (Pipelined)
(2) (2)
70V9189/79L7 Com'l Only Min. 22 12 7.5 7.5 5 5
____ ____
70V9189/79L9 Com'l & Ind Min. 25 15 12 12 6 6
____ ____
70V9189/79L12 Com'l Only Min. 30 20 12 12 8 8
____ ____
Parameter
(2)
Min. 19 10 6.5 6.5 4 4
____ ____
Max.
____ ____ ____ ____ ____ ____
Max.
____ ____ ____ ____ ____ ____
Max.
____ ____ ____ ____ ____ ____
Max.
____ ____ ____ ____ ____ ____
Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Clock High Time (Flow-Through) Clock Low Time (Flow-Through) Clock High Time (Pipelined) Clock Low Time (Pipelined) Clock Rise Time Clock Fall Time Address Setup Time Address Hold Time Chip Enable Setup Time Chip Enable Hold Time R/W Setup Time R/W Hold Time Input Data Setup Time Input Data Hold Time ADS Setup Time ADS Hold Time CNTEN Setup Time CNTEN Hold Time CNTRST Setup Time CNTRST Hold Time Output Enable to Data Valid Output Enable to Output Low-Z
(2)
(2)
(2)
3 3
____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____
3 3
____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____
3 3
____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____
3 3
____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____
3.5 0 3.5 0 3.5 0 3.5 0 3.5 0 3.5 0 3.5 0
____
4 0 4 0 4 0 4 0 4 0 4 0 4 0
____
4 1 4 1 4 1 4 1 4 1 4 1 4 1
____
4 1 4 1 4 1 4 1 4 1 4 1 4 1
____
6.5
____
9
____
12
____
12
____
(1) (1) (2)
2 1
____ ____
2 1
____ ____
2 1
____ ____
2 1
____ ____
Output Enable to Output High-Z
7 15 6.5
____
7 18 7.5
____
7 20 9
____
7 25 12
____
Clock to Data Valid (Flow-Through) Clock to Data Valid (Pipelined)
(2)
Data Output Hold After Clock High Clock High to Output High-Z(1) Clock High to Output Low-Z(1)
2 2 2
2 2 2
2 2 2
2 2 2
9
____
9
____
9
____
9
____
Port-to-Port Delay tCWDD tCCS Write Port Clock High to Read Data Delay Clock-to-Clock Setup Time
____ ____
24 9
____ ____
28 10
____ ____
35 15
____ ____
40 15
ns ns
4860 tbl 11
NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). This parameter is guaranteed by device characterization, but is not production tested. 2. The Pipelined output parameters (tCYC2, tCD2) apply to either or both the Left and Right ports when FT/PIPE = VIH. Flow-through parameters (tCYC1, tCD1) apply when FT/PIPE = VIL for that port. 3. All input signals are synchronous with respect to the clock except for the asynchronous Output Enable (OE), FT/PIPER, and FT/PIPEL.
6.42 7
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Read Cycle for Flow-Through Output (FT/PIPE"X" = VIL)(3,6)
tCYC1 tCH1 CLK
CE0
tCL1
tSC CE1
tHC
tSC
(4)
tHC
R/W
tSW tHW tSA tHA An + 1 tCD1 tDC Qn tCKLZ
(1)
ADDRESS
(5)
An
An + 2
An + 3 tCKHZ (1)
DATAOUT
Qn + 1
(1)
Qn + 2 tOLZ (1) tDC
tOHZ
OE
(2)
tOE
4860 drw 06
Timing Waveform of Read Cycle for Pipelined Output (FT/PIPE"X" = VIH)(3,6)
tCYC2 tCH2 CLK
CE0
tCL2
tSC CE1
tHC
tSC
(4)
tHC
R/W
tSW tSA
tHW tHA An + 1 (1 Latency) tCD2 Qn tCKLZ
(1)
ADDRESS(5)
An
An + 2 tDC Qn + 1
An + 3
DATAOUT
Qn + 2 tOLZ(1)
(6)
tOHZ(1)
OE
(2)
tOE
4860 drw 07 NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 2. OE is asynchronously controlled; all other inputs are synchronous to the rising clock edge. 3. ADS = VIL, CNTEN and CNTRST = VIH. 4. The output is disabled (High-Impedance state) by CE0 = VIH or CE1 = VIL following the next rising edge of the clock. Refer to Truth Table 1. 5. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 6. "X' here denotes Left or Right port. The diagram is with respect to that port.
6.42 8
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of a Bank Select Pipelined Read(1,2)
tCH2 CLK tSA ADDRESS(B1) tSC
CE0(B1)
tCYC2 tCL2
tHA A0 tHC tSC tCD2 tHC tCD2 Q0 tDC tCKHZ(3) Q1 tDC A3 A4 tCD2 Q3 tCKLZ
(3)
A1
A2
A3
A4
A5
A6
DATAOUT(B1) tSA ADDRESS(B2) tHA A0 A1
tCKHZ (3) A5 A6
A2
tSC tHC
CE0(B2)
tSC
tHC tCD2 tCKHZ Q2
(3)
tCD2 tCKLZ (3)
4860 drw 08
DATAOUT(B2) tCKLZ(3)
Q4
Timing Waveform of a Bank Select Flow-Through Read(6)
tCH1 CLK tSA ADDRESS(B1) tSC tH
A
tCYC1 tCL1
A0 tHC
A1
A2
A3
A4
A5
A6
CE0(B1)
tSC tHC tCD1 tCD1 D0 tDC tSA tHA A0 A1 A2 A3 A4 A5 A6 tCKHZ D1 tDC
(1)
tCD1 D3 tCKLZ
(1)
tCD1 D5 tCKHZ(1) tCKLZ
(1)
DATAOUT(B1)
ADDRESS(B2)
tSC tHC CE0(B2) tSC tHC tCD1 DATAOUT(B2) tCKLZ
(1)
tCKHZ D2
(1)
tCD1 tCKLZ
(1)
tCKHZ D4
(1)
, 4860 drw 08a
NOTES: 1. B1 Represents Bank #1; B2 Represents Bank #2. Each Bank consists of one IDT70V9089/79 for this waveform, and are setup for depth expansion in this example. ADDRESS(B1) = ADDRESS(B2) in this situation. 2. OE and ADS = VIL; CE1(B1), CE1(B2), R/W, CNTEN, and CNTRST = VIH. 3. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 4. CE0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. 5. OE = VIL for the Right Port, which is being read from. OE = VIH for the Left Port, which is being written to. 6. If tCCS < maximum specified, then data from right port READ is not valid until the maximum specified for tCWDD. If tCCS > maximum specified, then data from right port READ is not valid until tCCS + tCD1. tCWDD does not apply in this case.
6.42 9
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform with Port-to-Port Flow-Through Read(4,5,7)
CLK "A" tSW tHW R/W "A" tSA ADDRESS "A" tHA
NO MATCH
MATCH
tSD DATAIN "A"
VALID
tHD
tCCS CLK "B"
(6)
tCD1 R/W "B" tSW tSA ADDRESS "B" tHW tHA
NO MATCH
MATCH
tCWDD DATAOUT "B" tDC
(6)
tCD1
VALID VALID
tDC
4860 drw 09
NOTES: 1. B1 Represents Bank #1; B2 Represents Bank #2. Each Bank consists of one IDT70V9189/79 for this waveform, and are setup for depth expansion in this example. ADDRESS(B1) = ADDRESS(B2) in this situation. 2. OE, and ADS = VIL; CE1(B1), CE1(B2), R/W, CNTEN, and CNTRST = VIH. 3. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 4. CE0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. 5. OE = VIL for the Right Port, which is being read from. OE = VIH for the Left Port, which is being written to. 6. If tCCS < maximum specified, then data from right port READ is not valid until the maximum specified for tCWDD. If tCCS > maximum specified, then data from right port READ is not valid until tCCS + tCD1. tCWDD does not apply in this case. 7. All timing is the same for both Left and Right ports. Port "A" may be either Left or Right port. Port "B" is the opposite from Port "A".
6.42 10
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Pipelined Read-to-Write-to-Read (OE = VIL)(3)
tCYC2 tCH2 tCL2 CLK
CE0
tSC CE1
tHC
tSW tHW R/W tSW tHW
ADDRESS
(4)
An tSA tHA
An +1
An + 2
An + 2 tSD tHD Dn + 2
An + 3
An + 4
DATAIN
(2)
tCD2 Qn READ
tCKHZ
(1)
tCKLZ
(1)
tCD2 Qn + 3
DATAOUT
NOP
(5)
WRITE
READ
4860 drw 10
Timing Waveform of Pipelined Read-to-Write-to-Read (OE Controlled)(3)
tCH2 CLK
CE0
tCYC2 tCL2
tSC CE1
tHC
tSW tHW R/W tSW tHW
ADDRESS DATAIN
(4)
An tSA tHA
An +1
An + 2 tSD tHD
An + 3
An + 4
An + 5
(2)
tCD2 Qn tOHZ(1)
Dn + 2
Dn + 3
tCKLZ(1)
tCD2 Qn + 4
DATAOUT
OE
READ
WRITE
READ
4860 drw 11
NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 2. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 3. CE0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. "NOP" is "No Operation". 4. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 5. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity.
6.42 11
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Flow-Through Read-to-Write-to-Read (OE = VIL)(3)
tCH1 CLK tCYC1 tCL1
CE0
tSC CE1
tHC
tSW tHW R/W tSW tHW
ADDRESS
(4)
tSA DATAIN
(2)
An tHA
An +1
An + 2
An + 2 tSD tHD Dn + 2
An + 3
An + 4
tCD1 Qn tDC READ
tCD1 Qn + 1 tCKHZ NOP
(5) (1)
tCD1
tCD1 Qn + 3 tDC
4860 drw 12
DATAOUT
tCKLZ WRITE
(1)
READ
Timing Waveform of Flow-Through Read-to-Write-to-Read (OE Controlled)(3)
tCYC1 tCH1 tCL1 CLK
CE0
tSC CE1
tHC
tSW tHW R/W ADDRESS
(4)
tSW tHW An tSA tHA An +1 An + 2 tSD tHD Dn + 2
(2)
An + 3
An + 4
An + 5
DATAIN tCD1 Qn tOHZ
OE
(1)
Dn + 3
tDC
tOE tCD1
(1)
tCD1 Qn + 4 tDC
DATAOUT
tCKLZ
READ
WRITE
READ
4860 drw 13
NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 2. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 3. CE0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. "NOP" is "No Operation". 4. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 5. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity.
6.42 12
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Pipelined Read with Address Counter Advance(1)
tCH2 CLK tSA ADDRESS An tSAD tHAD
ADS
tCYC2 tCL2
tHA
tSAD tHAD
CNTEN
tSCN tHCN tCD2
DATAOUT
Qx - 1(2)
Qx tDC
Qn
Qn + 1
Qn + 2(2)
Qn + 3
READ EXTERNAL ADDRESS
READ WITH COUNTER
COUNTER HOLD
READ WITH COUNTER
4860 drw 14
Timing Waveform of Flow-Through Read with Address Counter Advance(1)
tCH1 CLK tSA ADDRESS tHA tCYC1 tCL1
An tSAD tHAD
ADS
tSAD tHAD tSCN tHCN
CNTEN
tCD1 DATAOUT Qx(2) tDC READ EXTERNAL ADDRESS READ WITH COUNTER COUNTER HOLD READ WITH COUNTER
4860 drw 15
Qn
Qn + 1
Qn + 2
Qn + 3(2)
Qn + 4
NOTES: 1. CE0 and OE = VIL; CE1, R/W, and CNTRST = VIH. 2. If there is no address change via ADS = VIL (loading a new address) or CNTEN = VIL (advancing the address), i.e. ADS = VIH and CNTEN = VIH, then the data output remains constant for subsequent clocks.
6.42 13
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Write with Address Counter Advance (Flow-Through or Pipelined Outputs)(1)
tCH2 CLK tSA ADDRESS tHA tCYC2 tCL2
An
INTERNAL(3) ADDRESS tSAD tHAD
ADS
An(7)
An + 1
An + 2
An + 3
An + 4
CNTEN(7)
tSD tHD DATAIN Dn WRITE EXTERNAL ADDRESS Dn + 1 Dn + 1 Dn + 2 Dn + 3 Dn + 4
WRITE WRITE WITH COUNTER COUNTER HOLD
WRITE WITH COUNTER
4860 drw 16
Timing Waveform of Counter Reset (Pipelined Outputs)(2)
tCH2 CLK tSA tHA ADDRESS(4) INTERNAL(3) ADDRESS R/W
ADS CNTEN
tCYC2 tCL2
An Ax (6) tSW tHW
An + 1
An + 2
0
1
An
An + 1
tSAD tHAD tSCN tHCN tSRST tHRST
CNTRST
tSD
tHD D0 Q0 Q1 READ ADDRESS n READ ADDRESS n+1 Qn
DATAIN DATAOUT(5) COUNTER RESET
(6)
WRITE ADDRESS 0
READ ADDRESS 0
READ ADDRESS 1
NOTES: 4860 drw 17 1. CE0 and R/W = VIL; CE1 and CNTRST = VIH. 2. CE0 = VIL; CE1 = VIH. 3. The "Internal Address" is equal to the "External Address" when ADS = VIL and equals the counter output when ADS = VIH. 4. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 5. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 6. No dead cycle exists during counter reset. A READ or WRITE cycle may be coincidental with the counter reset cycle. ADDR0 will be accessed. Extra cycles are shown here simply for clarification. 7. CNTEN = VIL advances Internal Address from `An' to `An +1'. The transition shown indicates the time required for the counter to advance. The `An +1' Address is written to during this cycle.
6.42 14
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Functional Description
The IDT70V9189/79 provides a true synchronous Dual-Port Static RAM interface. Registered inputs provide minimal set-up and hold times on address, data, and all critical control inputs. All internal registers are clocked on the rising edge of the clock signal, however, the self-timed internal write pulse is independent of the LOW to HIGH transition of the clock signal. An asynchronous output enable is provided to ease asynchronous bus interfacing. Counter enable inputs are also provided to staff the operation of the address counters for fast interleaved memory applications. CE0 = VIH or CE1 = VIL for one clock cycle will power down the internal circuitry to reduce static power consumption. Multiple chip enables allow easier banking of multiple IDT70V9189/79's for depth expansion configurations. When the Pipelined output mode is enabled, two cycles are required with CE0 = VIL and CE1 = VIH to re-activate the outputs.
Depth and Width Expansion
The IDT70V9189/79 features dual chip enables (refer to Truth Table I) in order to facilitate rapid and simple depth expansion with no requirements for external logic. Figure 4 illustrates how to control the varioius chip enables in order to expand two devices in depth. The IDT70V9189/79 can also be used in applications requiring expanded width, as indicated in Figure 4. Since the banks are allocated at the discretion of the user, the external controller can be set up to drive the input signals for the various devices as required to allow for 18-bit or wider applications.
A16/A15(1)
IDT70V9189/79
CE0 CE1 VDD
IDT70V9189/79
CE0 CE1 VDD
Control Inputs
Control Inputs
IDT70V9189/79
CE1 CE0
IDT70V9189/79
CE1 CE0 CNTRST CLK ADS CNTEN R/W OE
Control Inputs
Control Inputs
4860 drw 18
Figure 4. Depth and Width Expansion with IDT70V9189/79
NOTE: 1. A16 is for IDT70V9189. A15 is for IDT70V9179.
6.42 15
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Ordering Information
IDT XXXXX Device Type A Power 99 Speed A Package A Process/ Temperature Range Blank I
Commercial (0C to +70C) Industrial (-40C to +85C)
PF
100-pin TQFP (PN100-1)
6 7 9 12
Commercial Only Commercial Only Commercial & Industrial Commercial Only
Speed in nanoseconds
L
Low Power
.
70V9189 576K (64K x 9-Bit) Synchronous Dual-Port RAM 70V9179 288K (32K x 9-Bit) Synchronous Dual-Port RAM
4860 drw 19
IDT Clock Solution for IDT70V9189/79 Dual-Port
Dual-Port I/O Specitications IDT Dual-Port Part Number Voltage I/O Input Capacitance Clock Specifications Input Duty Cycle Requirement Maximum Frequency Jitter Tolerance IDT PLL Clock Device IDT Non-PLL Clock Device 49FCT3805 49FCT3805D/E 74FCT3807 74FCT3807D/E
4860 tbl 12
70V9189/79
3.3
LVTTL
9pF
40%
100
150ps
2305 2308 2309
6.42 16
IDT70V9189/79L High-Speed 64/32K x 9 Dual-Port Synchronous Pipelined Static RAM
Industrial and Commercial Temperature Ranges
Datasheet Document History
9/30/99: 11/12/99: 1/10/01: Initial Public Release Replaced IDT logo Page 3 Changed information in Truth Table II Page 4 Increased storage temperature parameters Clarified TA parameter Page 5 DC Electrical parameters-changed wording from "open" to "disabled" Changed 200mV to 0mV in notes Removed Preliminary status Consolidated multiple devices into one datasheet Changed naming conventions from VCC to VDD and from GND to Vss Removed I-temp footnote Page 2 Added date revision to pin configuration Page 4 Added Junction Temperature to Absolute Maximum Ratings Table Added Ambient Temperature footnote Page 5 Added I-temp numbers for 9ns speed to the DC Electrical Characteristics Table Added 6ns speed DC power numbers to the DC Electrical Characteristics Table Page 7 Added I-temp for 9ns speed to AC Electrical CharacteristicsTable Added 6ns speed AC timing numbers to the AC Electrical Characteristics Table Page 15 Added 6ns speed grade and 9ns I-temp to ordering information Added IDT Clock Solution Table
01/15/04:
CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054
for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com
6.42 17
for Tech Support: 831-754-4613 DualPortHelp@idt.com
The IDT logo is a registered trademark of Integrated Device Technology, Inc.

▲Up To Search▲

Price & Availability of IDT70V9189L9PFI

	To Download IDT70V9189L9PFI Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .